SVENSK STANDARD SS-EN 1597-1
Handläggande organ Fastställd Utgåva Sida
SVENSK MATERIAL- & MEKANSTANDARD, SMS 1998-03-20 1 1 (1+7+7)
SIS FA STSTÄLL ER O CH UTGE R S VEN S K STA ND ARD SAMT S ÄLJE R N ATIONELL A, E UROP EI SK A OCH I NTERN ATION ELLA STAND ARD PUBLIK A TION ER ©
ICS 25.160.20 © Innehållet i svensk standard är upphovsrättsligt skyddat. SIS har copyright till svensk standard.
Standarder kan beställas hos SIS som även lämnar all- männa upplysningar om svensk och utländsk standard.
Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08 - 610 30 00. Telefax: 08 - 30 77 57
Upplysningar om sakinnehållet i standarden lämnas av SMS.
Telefon: 08 - 459 56 00. Telefax: 08 - 667 85 42 E-post: info@sms-standard.se
Prisgrupp P Tryckt i april 1998
Welding consumables – Test
methods – Part 1: Test piece for all- weld metal test specimens in steel, nickel and nickel alloys
The European Standard EN 1597-1:1997 has the status of a Swedish Standard. This document con- tains the official English version of EN 1597-1:1997 with a Swedish translation.
This standard has been developed in collaboration with the Swedish Welding Commission.
This standard supersedes the Swedish Standards SS 06 10 01, edition 1, SS 06 11 01, edition 2 and
Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.
Tillsatsmaterial för svetsning – Provningsmetoder – Del 1: Prov för helsvetsprovstavar i stål, nickel och nickellegeringar
Europastandarden EN 1597-1:1997 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 1597-1:1997 med svensk översättning.
Denna standard har utarbetats i samarbete med Svetskommissionen.
Standarden ersätter SS 06 10 01, utgåva 1, SS 06 11 01,
Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.
SS 06 13 01, edition 1. SS 06 13 01, utgåva 1.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1597-1
July 1997
ICS 25.160.20
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS
© 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members
Descriptors: welding, arc welding, steels, nickel, nickel alloys, fillers, weld metal, joining, preparation, test specimen, mechanical properties, classifications, tests
English version
Welding consumables – Test methods –
Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys
Produits consommables pour le soudage – Méthodes d’essai – Partie 1: Assemblage d’essai d’éprouvettes prélevées dans le métal fondu hors dilution pour le soudage de l’acier, du nickel et des alliages de nickel
Schweißzusätze – Prüfmethoden – Teil 1:
Prüfstück zur Entnahme von Proben aus reinem Schweißgut an Stahl, Nickel und
Nickellegierungen
This European Standard was approved by CEN on 1997-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
The European Standards exist in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1597-1
Juli 1997
ICS 25.160.20
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS
© 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members
Ref. Nr. EN 1597-1:1997 Sv Nyckelord: svetsning,bågsvetsning, stål, nickel, nickellegeringar, tillsatsmaterial, svetsgods, förbindning, fogberedning,
provstav, mekaniska egenskaper, indelningar, prov
Svensk version
Tillsatsmaterial för svetsning – Provningsmetoder – Del 1: Prov för helsvetsprovstavar i stål,
nickel och nickellegeringar
Produits consommables pour le soudage – Méthodes d’essai – Partie 1: Assemblage d’essai d’éprouvettes prélevées dans le métal fondu hors dilution pour le soudage de l’acier, du nickel et des alliages de nickel
Welding consumables – Test methods – Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys
Schweißzusätze – Prüfmethoden – Teil 1: Prüfstück zur Entnahme von Proben aus reinem Schweißgut an Stahl, Nickel und Nickellegierungen
Denna standard är den officiella svenska versionen av EN 1597-1:1997. För översättningen svarar SIS.
Denna europastandard antogs av CEN 1997-06-29. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard.
Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar.
Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna.
CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 2
EN 1597-1:1997
Contents
Page
Foreword ... 3
Introduction ... 4
1 Scope ... 4
2 Normative references ... 4
3 General requirements ... 4
4 Test plate material ... 4
5 Preparation of test piece ... 5
6 Welding conditions ... 5
7 Heat treatment ... 6
8 Position of specimens and specimen dimensions ... 6
9 Retests ... 6
10 Test report ... 7
Sida 2 EN 1597-1:1997
Innehåll
Sida
Förord ... 3
Orientering... 4
1 Omfattning ... 4
2 Bindande referenser ... 4
3 Allmänna krav ... 4
4 Provplåtar ... 4
5 Provstycke ... 5
6 Svetsningsbetingelser ... 5
7 Värmebehandling ... 6
8 Läge och mått för provstav ... 6
9 Omprov ... 6
10 Provningsrapport ... 7
Page 3
EN 1597-1:1997
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 121
”Welding”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998.
This standard consists of the following parts:
Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys
Part 2: Preparation of test piece for single-run and two-run technique test speci- mens in steel
Part 3: Classification testing of positional capability of welding consumables in a fillet weld
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Sida 3 EN 1597-1:1997
Förord
Denna europastandard har utarbetats av den tekniska kommittén CEN/TC 121
”Welding” med sekretariat vid DS.
Denna europastandard skall ges status som nationell standard, antingen genom publikation av en identisk text eller genom ikraftsättning, senast i januari 1998.
Motstridande nationella standarder skall dras in senast i januari 1998.
Denna standard består av följande delar:
Del 1: Prov för helsvetsprovstav i stål, nickel och nickellegeringar
Del 2: Framställning av prov för provstavar i ensträngs- och tvåsträngsteknik i stål
Del 3: Provning av lägessvetsbarhet hos svetstillsatsmaterial i en kälsvets Enligt CEN/CENELECS interna bestämmelser är följande länder förpliktade att införa denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spa- nien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 4
EN 1597-1:1997
Introduction
It should be noted that the mechanical properties of all-weld metal test specimens used to classify the welding consumables could vary from those obtained in pro- duction joints because of differences in welding procedure such as electrode diame- ter, width of weave, welding position and material composition.
Test conditions prescribed and results required should not be considered to be requirements or expectations for a procedure qualification.
1 Scope
This standard specifies preparation of test piece and specimens. The purpose is to determine mechanical properties of all-weld metal where required by the consum- able classification standard or for other purposes in arc welding of steel, nickel and nickel alloys.
This standard is not applicable to single- or two-pass welding or fillet welding. For these cases, EN 1597-2 and EN 1597-3 apply.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
EN 875 Destructive tests on welds in metallic materials – Impact tests – Test specimen location, notch orientation and examination
EN 876 Destructive tests on welds in metallic materials – Longitudinal tensile test on weld metal in fusion welded joints
EN 1597-2 Welding consumables – Test methods – Part 2: Preparation of test piece for single and two run technique test specimens in steel EN 1597-3 Welding consumables – Test methods – Part 3: Classification test-
ing of positional capability of welding consumables in a fillet weld EN ISO 13916 Welding – Guidance on the measurement of preheating tempera-
ture, interpass temperature and preheat maintenance tempera- ture (ISO 13916:1996)
3 General requirements
Welding consumables to be tested shall be representative of the manufacturer's products to be classified or tested. Test pieces shall be prepared as described below.
4 Test plate material
The material to be used for the test piece shall be compatible with the weld metal provided by the welding consumable tested. Alternatively the groove edges and the backing strip shall be built up with at least two layers using the welding con- sumable being tested.