D E S K L I F T D B 1
DB1: 24V DC. Max. thrust 1000 N
Features:
• Plug mounted on DB1 for connection to CBD with separate DESKLINE® motor cable
• Max. thrust 1000 N (per leg)
• Max. speed with fast motor: 42 mm/sec. with CBD
• Built-in limit switches (not adjustable)
• Standard stroke length 500 mm
• Protection class IP 20
• Installation dimension:
94 mm + stroke with piston rod eye type: 0 89 mm + stroke with piston rod eye type: 1
• Dimension outer tube: ø32 mm ± 0.3 mm
• Dimension motor housing 246 x 100 x 90 mm
• Bending moment is transferred to the customer's guidance
• Low noise level (ca. 45dB)
• Brake single acting as LA31
• Typical current consumption: 2.5 Amp. at max. thrust (per DB1) for standard motor and 3.1 Amp for 24 V fast motor.
• Colour: Black plastic motor housing, outer tube aluminium and inner tube stainless steel
• Hall sensor (enables parallel drive with control box CBD)
• Ambient temperature: +5°C to +40°C
• Approved according to EN60335-1 and UL 73
Options:
• Two different piston rod eyes
• 24 V Fast motor
The DB1 is the first LINAK built-in actuator in the DESKLINE product range.
The DB1 is specially designed for easy integration in the customer's guidances, to achieve the optimum freedom of design for desk applications.
The DB1 (DESKLINE® Built-in) is designed with a staggered housing from the gear housing to achieve a very low installation dimension.
The DB1 can either be a part of a 2 parallel system, 3 parallel or 2 + 2 parallel systems. The parallel drive and the control box CBD1, CBD3 or CBD3B (only 2 parallel) keep the desk surface level even with an uneven load.
The control box i designed with a soft start/stop function.
WE IMPROVE YOUR LIFE
DB1 dimensions:
Mounting guidelines for DB1
The plastic motor housing is prepared for four pcs. M6 nuts or Unbraco for mounting on the customer's guidance/tabletop.
We advise you to fasten the DB1 by means of four pcs. M6 screws of a good quality and a suitable length.
DB1 with solid piston rod eye
Piston rod eye:
DB1001E LINAK A/S
4 x ø6.3
34
22Ø 32±0.3Ø
70 Ø
68
71.5 246
16344
90
66 85 100
46 580
594 = S + 94
10
8.5 8.5
DB1 with plastic piston rod eye
Piston rod eye:
DB1002E LINAK A/S
4 x ø6.3
22ø
580
34
32±0.3ø 70
Ø
68
71.5 246
163
44
90
66 85 100
45 589 = S + 89
8.5 8.5
10
DB1
Ordering example:
Note:
Motor cables must be ordered separately.
Cable description: Ordering no.:
900 mm straight black cable: 0567006 1800 mm straight black cable: 0567007 2300 mm straight black cable: 0567015
- Order two pcs. for 2 - parallel systems - Order three pcs. for 3 - parallel systems - Order four pcs. for 2 + 2 parallel systems
0 = 24 V motor 3 = Fast motor
Cable: 0 = Without cable
1 = DL2 Plastic piston rod eye for bottom fixing Technical specifi cations
Type
DB1 2 parallel DB1 3 parallel DB1 fast motor 2 parallel
DB1 fast motor 3 parallel
Spindle pitch (mm) 12 12
15
15
Thrust max. pr.
DB1 (N) 1000 1000
1000
533
Self-lock pr. DB1
(N) 1000 1000
1000
1000
Speed at full load (mm/s)
21 18
28
28
Duty cycle
(%) 10 10
10
10
*Amp at full load (CBD1)
2.0 2.1
3.1
2.4
Above measurements are made in connection with control box CBD1.
The standard combinations are standard motor combined with 12 mm pitch and fast motor combined with 15 mm pitch.
Specifications subject to change without prior notice.
It is the responsibility of the product user to determine the suitability of LINAK A/S products for a specific application. LINAK will at point of delivery replace/repair defective products covered by the warranty if promptly returned to the factory. No liability is assumed beyond such replacement/repair.
Copyright © LINAK 03.02 . MA M9-02-076-E . Chapter 2.2
Above data are typical values. Measured with control box CBD1.
2-parallel system with standard motor:
3-parallel system with standard motor:
10 15 20 25 30
2-parallel system with fast motor:
3-parallel system with fast motor:
