• No results found

SVENSK STANDARD SS-EN ISO

N/A
N/A
Protected

Academic year: 2022

Share "SVENSK STANDARD SS-EN ISO"

Copied!
11
0
0

Loading.... (view fulltext now)

Full text

(1)

SVENSK STANDARD SS-EN ISO 683-17

Handläggande organ Fastställd Utgåva Sida

SVENSK MATERIAL- & MEKANSTANDARD, SMS 1999-10-15 1 1 (1+24+24)

© Copyright SIS. Reproduction in any form without permission is prohibited.

ICS 77.140.10; 77.140.20

Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard.

Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08 - 610 30 00. Telefax: 08 - 30 77 57 E-post: sis.sales@sis.se. Internet: www.sisforlag.se

Upplysningar om sakinnehållet i standarden lämnas av SMS.

Telefon: 08 - 459 56 00. Telefax: 08 - 667 85 42 E-post: info@sms-standard.se

Prisgrupp S Tryckt i september 2000

Heat-treated steels, alloy steels and free-cutting steels –

Part 17: Ball and roller bearing steels (ISO 683-17:1999)

The European Standard EN ISO 683-17:1999 has the status of a Swedish Standard. This document con- tains the official English version of EN ISO 683-17:

1999 with a Swedish translation.

This Standard supersedes the Swedish Standard SS 14 22 58, edition 3.

Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.

Stål för värmebehandling,

legerade stål och automatstål – Del 17: Kullagerstål

(ISO 683-17:1999)

Europastandarden EN ISO 683-17:1999 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN ISO 683-17:1999 med svensk översättning.

Standarden ersätter SS 14 22 58, utgåva 3.

Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.

(2)

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

EN ISO 683-17

October 1999

ICS 77.140.10; 77.140.20

CEN

European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung

Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS

© 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members

Ref. No. EN ISO 683-17:1999 E

English version

Heat-treated steels, alloy steels and free-cutting steels – Part 17: Ball and roller bearing steels (ISO 683-17:1999)

Acier pour traitement thermique, aciers alliés et aciers pour décolletage – Partie 17: Aciers pour roulements (ISO 683-17:1999)

Für eine Wärmebehandlung bestimmte Stähle, legierte Stähle und Automatenstähle – Teil 17:

Wälzlagerstähle (ISO 683-17:1999)

This European Standard was approved by CEN on 5 September 1999.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German).

A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

(3)

EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

EN ISO 683-17

Oktober 1999

ICS 77.140.10; 77.140.20

CEN

European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung

Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS

© 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members

Ref. Nr. EN ISO 683-17:1999 Sv

Svensk version

Stål för värmebehandling, legerade stål och automatstål – Del 17: Kullagerstål (ISO 683-17:1999)

Acier pour traitement thermique, aciers alliés et aciers pour

décolletage – Partie 17: Aciers pour roulements (ISO 683-17:1999)

Heat-treated steels, alloy steels and free-cutting steels – Part 17:

Ball and roller bearing steels (ISO 683-17:1999)

Für eine Wärmebehandlung bestimmte Stähle, legierte Stähle und Automatenstähle – Teil 17:

Wälzlagerstähle (ISO 683-17:1999)

Denna standard är den officiella svenska versionen av EN ISO 683-17:1999. För översättningen svarar SIS.

Denna europastandard antogs av CEN den 5 september 1999.

CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar.

Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna.

CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.

(4)

Page 2

EN ISO 683-17:1999

Contents

Page

Foreword ... 3

1 Scope ... 4

2 Normative references ... 4

3 Terms and definitions ... 5

4 Ordering and designation ... 5

5 Requirements ... 6

6 Inspection, testing and conformance of products ... 8

7 Marking ... 9

Annex A (normative) Supplementary or special requirements ... 18

Annex B (informative) Content of microscopic non-metallic inclusions ... 20

Annex C (informative) Designations of comparable steels ... 22

Bibliography ... 23

Annex ZA (normative) Normative references to international publications with their relevant European publications ... 24

(5)

Sida 2 EN ISO 683-17:1999

Innehåll

Sida

Förord ... 3

1 Omfattning ... 4

2 Normativa referenser ... 4

3 Termer och definitioner ... 5

4 Beställning och beteckning ... 5

5 Fordringar ... 6

6 Kontroll, provning och produkters överensstämmelse med fordran ... 8

7 Märkning ... 9

Bilaga A (normativ) Tilläggs- och specialfordringar ... 18

Bilaga B (informativ) Innehåll av mikroskopiska icke-metalliska inneslutningar ... 20

Bilaga C (informativ) Beteckningar för jämförbara stålsorter ... 22

Litteraturförteckning ... 23

Bilaga ZA (normativ) Normativa hänvisningar till internationella publikationer med deras relevanta europeiska publikationer ... 24

(6)

Page 3

EN ISO 683-17:1999

Foreword

The text of the International Standard ISO 683-17:1999 has been prepared by Technical Committee ISO/TC 17 ”Steel” in collaboration with Technical Committee ECISS/TC 23, ”Steels for heat treatment, alloy steels and free-cutting steels – Qualities and dimensions”, the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2000, and conflicting national standards shall be withdrawn at the latest by April 2000.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

Endorsement notice

The text of the International Standard ISO 683-17:1999 was approved by CEN as a European Standard without any modification.

NOTE: Normative references to International Standards are listed in annex ZA (normative).

(7)

Sida 3 EN ISO 683-17:1999

Förord

Texten i den internationella standarden ISO 683-17:1999 har utarbetats av den tekniska kommittén ISO/TC 17 ”Steel” i samarbete med den tekniska kommit- tén ECISS/TC 23, Steels for heat treatment, alloy steels and free-cutting steels – Qualities and dimensions. Sekretariatet hålls av DIN.

Denna europastandard skall ges status av nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast April 2000, och mot- stridande nationella standarder skall dras in senast April 2000.

Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.

Ikraftsättningsnotering

Texten i den internationella standarden ISO 683-17:1999 är godkänd av CEN som en europastandard utan någon ändring.

Anm. – Normativa referenser till internationella publikationer finns i bilaga ZA (normativ).

(8)

Page 4

EN ISO 683-17:1999

Heat-treated steels, alloy steels and free-cutting steels — Part 17:

Ball and roller bearing steels

1 Scope

1.1 This part of ISO 683 applies to the products and heat-treatment conditions given in Table 1 and the surface conditions given in Table 2.

1.2 This part of ISO 683 gives the technical delivery requirements for five groups of wrought ball and roller bearing steels as listed in Table 3, namely:

a) through-hardening bearing steels (steels with about 1 % C and 1 % to 2 % Cr);

b) case-hardening bearing steels;

c) induction-hardening bearing steels (unalloyed and alloyed);

d) stainless bearing steels;

e) high temperature bearing steels.

1.3 In special cases variations in these technical delivery requirements or additions to them may form the subject of an agreement at the time of inquiry and order (see annex A).

1.4 In addition to this part of ISO 683, the general technical delivery requirements of ISO 404 are applicable.

2 Normative references

The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 683. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 683 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.

ISO 377:1997, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing.

ISO 404:1992, Steel and steel products — General technical delivery requirements.

ISO 642:1999, Steels — Hardenability test by end quenching (Jominy test).

ISO 643:1983, Steels — Micrographic determination of the ferritic or austenitic grain size.

ISO 1035-1:1980, Hot-rolled steel bars — Part 1: Dimensions of round bars.

ISO 1035-4:1982, Hot-rolled steel bars — Part 4: Tolerances.

ISO 3763:1976, Wrought steels — Macroscopic methods for assessing the content of non-metallic inclusions.

ISO 3887:1976, Steel, non-alloy and low-alloy — Determination of depth of decarburization.

(9)

Sida 4 EN ISO 683-17:1999

Stål för värmebehandling, legerade stål och automatstål – Del 17: Kullagerstål

1 Omfattning

1.1 Denna del av ISO 683 gäller för produkterna och värmebehandlingstillstån- den angivna i tabell 1 och yttillstånden angivna i tabell 2.

1.2 Denna del av ISO 683 anger tekniska leveransbestämmelser för fem grupper av plastiskt bearbetat kullagerstål såsom listats i tabell 3, nämligen:

a) genomhärdande kullagerstål (stål med omkring 1 % C och 1 % till 2 % Cr), b) sätthärdningskullagerstål

c) induktionshärningskullagerstål (olegerat och legerat), d) rostfritt kullagerstål,

e) högtemperatur kullagerstål.

1.3 I särskilda fall kan avvikelser från dessa tekniska leveransbestämmelser eller tillägg till dem bli föremål för överenskommelse vid förfrågan och beställ- ning (se Bilaga A).

1.4 Utöver denna del av ISO 683 är de allmänna tekniska leveransbestämmel- serna enligt ISO 404 tillämpliga.

2 Normativa hänvisningar

Följande bindande referenser innehåller fordringar som genom referens i texten också innebär fordringar för denna del av ISO 683. För daterade referenser gäller inte senare tillägg eller revideringar av dessa standarder. När överenskommelser baseras på denna del av ISO 683 uppmanas parterna att undersöka möjligheten att använda senaste utgåvan av nedanstående bindande referenser. För odaterade referenser gäller hänvisningen till den senaste utgåvan av dokumentet. ISOs och IECs medlemmar för register över gällande internationella standarder.

ISO 377:1997, Stål och stålprodukter – Uttag och provberedning av provstycken och provstavar för mekanisk provning (ISO 377:1977).

ISO 404:1992, Steel and steel products – General technical delivery requirements.

ISO 642:1999, Stål – Härdbarhetsprovning enligt jominy.

ISO 643:1983, Steels – Micrographic determination of the ferritic or austenitic grain size.

ISO 1035-1:1980, Hot-rolled steel bars – Part 1: Dimensions of round bars.

ISO 1035-4:1982, Hot-rolled steel bars – Part 4: Tolerances.

ISO 3763:1976, Wrought steels – Macroscopic methods .

ISO 3887:1976, Steel non-alloy and low-alloy – Determination of depth of decar- burization.

(10)

Page 5

EN ISO 683-17:1999

ISO 4948-1:1982, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition.

ISO 4967:1998, Steel — Determination of content of nonmetallic inclusions — Micrographic method using standard diagrams.

ISO 4969:1980, Steel — Macroscopic examination by etching with strong mineral acids.

ISO 5949:1983, Tool steels and bearing steels — Micrographic method for assessing the distribution of carbides using reference photomicrographs.

ISO 6506:19811), Metallic materials — Hardness test — Brinell test.

ISO 6929:1987, Steel products — Definitions and classification.

ISO 9443:1991, Heat-treatable and alloy steels — Surface quality classes for hot-rolled round bars and wire rods — Technical delivery conditions.

ISO/TR 9769:1991, Steel and iron — Review of available methods of analysis.

ISO 10474:1991, Steel and steel products — Inspection documents.

ISO 14284:1996, Steel and iron — Sampling and preparation of samples for the determination of chemical composition.

ENV 10247:1996, Metallographic test methods — Examination of steels using standard diagrams to assess the content of non-metallic inclusions.

3 Terms and definitions

For the purposes of this part of ISO 683, the terms and definitions for the product forms given in ISO 6929 apply.

The terms "unalloyed steel" and "alloyed steel" are as defined in ISO 4948-1.

4 Ordering and designation

The designation of the product on an order shall cover the following.

a) The designation of the product form (e. g. bar) followed by

1) either the designation of the dimensional standard and the dimensions and tolerances selected from it (see 5.6) or

2) the designation of any other document covering the dimensions and tolerances required for the product.

b) If a surface condition other than "hot worked" or a special surface quality is required 1) the surface condition (see Table 2), and

2) the surface quality (see 5.5).

c) A description of the steel comprising 1) a reference to this part of ISO 683;

2) the designation of the steel type (see Table 3);

3) the symbol for the heat-treatment condition on delivery (see Table 1);

4) the standard designation for the required type of inspection document (see ISO 10474);

5) the symbol and, where necessary, the details of this supplementary requirement (see annex A), if any supplementary requirement shall be complied with.

1) This International Standard has been replaced by ISO 6506-1, ISO 6506-2 and ISO 6506-3.

(11)

Sida 5 EN ISO 683-17:1999

ISO 4948-1:1982, Steels – Classificaton – Part 1: Classification of steels into unal- loyed and alloy steels based on chemical composition.

ISO 4967:1998, Steel – Determination of content of non-metallic inclusions – Mi- crographic method using standard diagrams.

ISO 4969:1980, Steel – Macroscopic examination by etching with strong mineral acids.

ISO 5949:1983, Tool steels and bearing steels – Micrographic method for assessing the distribution of carbide using reference micrographs.

ISO 6506:19811), Metallic materials – Hardness test – Brinell test.

ISO 6229:1987, Steel products – Definitions and classification.

ISO 9443:1991, Heat-treatable and alloy steels – Surface quality classes for hot- rolled round bars and wire rods – Technical delivery conditions.

ISO/TR 9769: Steel and iron – Review of available methods of analysis.

ISO 10474:1991, Steel and steel products – Inspection documents.

ISO 14284:1996, Steel and iron – Sampling and preparation of samples for the determination of chemical composition.

ENV 10247:1996, Metallographic test methods – Examination of steels using stan- dard diagrams to assess the content of non-metallic inclusions.

3 Termer och definitioner

Vid tillämpning av denna del av ISO 683 gäller gäller termer och definitioner för formvaror enligt ISO 6929. För termerna ”olegerat stål” och ”legerat stål” gäller ISO 4948-1.

4 Beställning och beteckning Beteckningen skall innehålla följande.

a) Beteckning för formvaran ( t ex. stång) följt av

1) endera beteckningen på formvarustandarden och dimensioner och tole- ranser från den (se 5.6) eller

2) beteckning på annat dokument som innehåller fordrade dimensioner och toleranser för formvaran.

b) Om annat ytutförande än ”varmbearbetat” eller om speciell ytbeskaffenhet önskas

1) ytutförandet (se tabell 2), och 2) ytbeskaffenhet (se 5.5).

c) En beskrivning av stålet innefattande 1) en referens till denna del av ISO 683, 2) beteckning för stålsorten (se tabell 3),

3) beteckning för värmebehandlingstillståndet vid leverans (se tabell 1), 4) standardens beteckning för den fordrade intygstypen (se ISO 10474), 5) beteckning och eventuella detaljer angående tilläggsfordringar (se annex A)

om tilläggsfordingar gäller.

1) Denna Internationella standard har ersatts av ISO 6506-1, ISO 6506-2 och ISO 6506-3.

References

Related documents

– ISO 11127-2:1993, Preparation of steel sub- strates before application of paints and related products – Test methods for non-metallic blast- cleaning abrasives – Part 2:

– ISO 11125-2, som oförändrad överförts till svensk standard SS-EN ISO 11125-2 Behand- ling av stålytor före beläggning med målnings- färg och liknande produkter –

Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 6: Determination of

– ISO 11125-1:1993, Preparation of steel substrates before application of paints and related prod- ucts – Test methods for metallic blast-cleaning abrasives – Part 1: Sampling, which

Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 3: Determination of apparent

– ISO 11125-1:1993, Preparation of steel substrates before application of paints and related prod- ucts – Test methods for metallic blast-cleaning abrasives – Part 1: Sampling, which

ISO 11904 is a series of standards which specify methods for the determination of sound immissions from sources located close to the ear in which situations the sound

This part of ISO 3864 gives principles, criteria and guidance for the design of graphical symbols for use in safety signs as defined in ISO 3864-1, and for the safety sign element