SVENSK STANDARD SS-EN 12070
Fastställd Utgåva Sida
2000-04-28 1 1 (1+9+9)
© Copyright SIS. Reproduction in any form without permission is prohibited.
ICS 25.160.20
Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard.
Postadress: SIS Förlag AB, 118 80 STOCKHOLM Telefon: 08 - 555 523 00. Telefax: 08 - 555 523 11 E-post: sis.sales@sis.se. Internet: www.sisforlag.se
Upplysningar om sakinnehållet i standarden lämnas av SIS.
Telefon: 08 - 555 520 00. Telefax: 08 - 555 520 01
Tryckt i augusti 2001
Welding consumables – Wire electrodes, wires and rods for arc welding of creep-resisting steels – Classification
The European Standard EN 12070:1999 has the status of a Swedish Standard. This document con- tains the official English version of EN 12070:1999 with a Swedish translation.
This standard has been developed in collaboration with the Swedish Welding Commission.
Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.
Tillsatsmaterial för svetsning – Trådelektroder, svetstråd och svetsstavar för bågsvetsning av varmhållfasta stål – Indelning
Europastandarden EN 12070:1999 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 12070:1999 med svensk översättning.
Denna standard har utarbetats i samarbete med Svetskommissionen.
Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12070
October 1999
ICS 25.160.20
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS
© 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members
Ref. No. EN 12070:1999 E
English version
Welding consumables – Wire electrodes, wires and rods for arc welding of creep-resisting steels – Classification
Produits consommables pour le soudage – Fils- électrodes, fils d'apport et baguettes d'apport pour le soudage à l’arc des aciers résistant au fluage – Classification
Schweißzusätze – Drahtelektroden, Drähte und Stäbe zum Lichtbogenschweißen von
warmfesten Stählen – Einteilung
This European Standard was approved by CEN on 3 September 1999.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German).
A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12070
Oktober 1999
ICS 25.160.20
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS
© 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members
Ref. Nr. EN 12070:1999 Sv
Svensk version
Tillsatsmaterial för svetsning – Trådelektroder, svetstråd och svetsstavar för bågsvetsning av varmhållfasta stål – Indelning
Produits consommables pour le soudage – Fils-électrodes, fils d'apport et baguettes d'apport pour le soudage à l’arc des aciers résistant au fluage – Classification
Welding consumables – Wire electrodes, wires and rods for arc welding of creep-resisting steels – Classification
Schweißzusätze – Drahtelektroden, Drähte und Stäbe zum
Lichtbogenschweißen von warmfesten Stählen – Einteilung
Denna standard är den officiella svenska versionen av EN 12070:1999. För över- sättningen svarar SIS.
Denna europastandard antogs av CEN den 3 september 1999.
CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar.
Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna.
CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 2
EN 12070:1999
Contents
Page
Foreword ... 3
Introduction ... 4
1 Scope ... 4
2 Normative references ... 4
3 Classification ... 4
4 Symbols and requirements ... 4
4.1 Symbol for the product/process ... 4
4.2 Symbol for the chemical composition of wire electrodes, wires and rods ... 5
5 Mechanical tests ... 6
5.1 Preheating and interpass temperatures ... 6
5.2 Pass sequence and welding conditions ... 7
6 Chemical analysis ... 7
7 Technical delivery conditions ... 7
8 Designation ... 7
Bibliography ... 9
Sida 2 EN 12070:1999
Innehåll
Sida
Förord ... 3
Inledning ... 4
1 Omfattning ... 4
2 Normativa hänvisningar ... 4
3 Indelning ... 4
4 Beteckningar och krav ... 4
4.1 Beteckning för produkten/metoden ... 4
4.2 Beteckning för kemisk sammansättning hos trådelektroder, svetstråd och svetsstavar ... 5
5 Mekanisk provning ... 6
5.1 Förhöjd arbetstemperatur och mellansträngstemperatur ... 6
5.2 Strängföljd och svetsdata ... 7
6 Kemisk analys ... 7
7 Tekniska leveransbestämmelser ... 7
8 Beteckning ... 7
Bibliografi ... 9
Page 3
EN 12070:1999
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 121
”Welding”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2000, and conflicting national standards shall be withdrawn at the latest by April 2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Sida 3 EN 12070:1999
Förord
Denna europastandard har utarbetats av den tekniska kommittén CEN/TC 121
”Welding” med sekretariat vid DS.
Denna europastandard skall ges status av nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast april 2000, och mot- stridande nationella standarder skall dras in senast april 2000.
Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 4
EN 12070:1999
Introduction
For creep-resisting steel welding consumables it should be noted that the me- chanical properties of all-weld metal test specimens used for classification will vary from those obtained in production joints because of differences in welding conditions, material composition and shielding gas or flux.
Although combinations of wires and fluxes supplied by individual companies can have the same grading, the individual wires and fluxes from different companies are not interchangeable unless verified in accordance with this standard.
1 Scope
This standard specifies requirements for classification of wire electrodes, wires and rods for gas tungsten arc welding, gas shielded metal arc welding and sub- merged arc welding of creep-resisting and low alloy elevated temperature steels.
The classification of the wire electrodes, wires and rods is based on their chemical composition.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
EN 759 Welding consumables – Technical delivery conditions for welding filler metals – Type of product, dimensions, tolerances and mark- ing
EN 1597-1 Welding consumables – Test methods – Part 1: Test piece for all- weld metal test specimens in steel, nickel and nickel alloys
EN ISO 13916 Welding – Guidance on the measurement of preheating tempera- ture, interpass temperature and preheat maintenance tempera- ture (ISO 13916:1996)
ISO 31-0:1992 Quantities and units – Part 0: General principles
3 Classification
A wire electrode, wire or rod is classified in accordance with its chemical composi- tion in table 1.
When the wire electrode, wire or rod is classified in combination with a gas or flux for welding the classification shall be prefixed with a symbol in accordance with clause 4 as appropriate.
As a consequence the classification is divided into two parts:
a) the first part gives a symbol indicating the product/process to be identified;
b) the second part gives a symbol indicating the chemical composition of the wire electrode, wire or rod.
4 Symbols and requirements
4.1 Symbol for the product/process
The symbol for the wire electrode, wire or rod used in the arc welding process shall be the letter G (gas shielded metal arc welding), S (submerged arc welding) and/or W (gas tungsten arc welding).