• No results found

SVENSK STANDARD SS-EN

N/A
N/A
Protected

Academic year: 2022

Share "SVENSK STANDARD SS-EN"

Copied!
11
0
0

Loading.... (view fulltext now)

Full text

(1)

SVENSK STANDARD SS-EN 10222-1

Handläggande organ Fastställd Utgåva Sida

SVENSK MATERIAL- & MEKANSTANDARD, SMS 1998-07-31 1 1 (1+16+16)

© Copyright SIS. Reproduction in any form without permission is prohibited.

ICS 77.140.85

Standarder kan beställas hos SIS som även lämnar all- männa upplysningar om svensk och utländsk standard.

Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08 - 610 30 00. Telefax: 08 - 30 77 57

Upplysningar om sakinnehållet i standarden lämnas av SMS.

Telefon: 08 - 459 56 00. Telefax: 08 - 667 85 42 E-post: info@sms-standard.se

Prisgrupp R Tryckt i maj 1999

Steel forgings for pressure pur- poses – Part 1: General require- ments for open die forgings

The European Standard EN 10222-1:1998 has the status of a Swedish Standard. This document con- tains the official English version of EN 10222-1:

1998 with a Swedish translation.

Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.

Smide av stål för tryckkärlsända- mål – Del 1: Allmänna bestämmel- ser för friformsmide

Europastandarden EN 10222-1:1998 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 10222-1:1998 med svensk översättning.

Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.

(2)

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

EN 10222-1

January 1998

ICS 77.140.85

CEN

European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung

Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS

© 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members

Ref. No. EN 10222-1:1998 E

Descriptors: iron and steel products, forgings, steels, pressure equipment, designation, manufacturing, surface condition, grades:quality, chemical composition, mechnical properties, sampling, tests, inspection, marking

English version

Steel forgings for pressure purposes –

Part 1: General requirements for open die forgings

Pièces forgées en acier pour appareils à pression – Partie 1: Prescriptions générales concernant les pièces obtenues par forgeage libre

Schmiedestücke aus Stahl für Drucksbehälter – Teil 1: Allgemeine Anforderungen an Freiform- schmiedestücke

This European Standard was approved by CEN on 26 October 1997.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

This European Standard exists in three official versions (English, French, German).

A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.

(3)

EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM

EN 10222-1

Januari 1998

ICS 77.140.85

CEN

European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung

Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS

© 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members

Ref. Nr. EN 10222-1:1998 Sv

Nyckelord: järn- och stålprodukter, smide, stål, tryckbärande anordningar, beteckning, tillverkning, ytbeskaffenhet, stålsorter, kemisk sammansättning, mekaniska egenskaper, provtagning, provning, kontroll, märkning

Svensk version

Smide av stål för tryckkärlsändamål – Del 1: Allmänna bestämmelser för friformsmide

Pièces forgées en acier pour appareils à pression – Partie 1:

Prescriptions générales concernant les pièces obtenues par forgeage libre

Steel forgings for pressure purposes – Part 1: General requirements for open die forgings

Schmiedestücke aus Stahl für Drucksbehälter – Teil 1: Allgemeine Anforderungen an Freiform-

schmiedestücke

Denna standard är den officiella svenska versionen av EN 10222-1:1998. För översättningen svarar SIS.

Denna europastandard antogs av CEN den 26 oktober 1997.

CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar.

Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna.

CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.

(4)

Page 2

EN 10222-1:1998

Contents

Page

Foreword ... 2

1 Scope ... 3

2 Normative references ... 3

3 Definitions ... 4

4 Classification and designation ... 4

5 Information to be supplied by the purchaser ... 4

6 Manufacture of the steel ... 5

7 Manufacture of the product ... 5

8 Surface condition and soundness ... 6

9 Chemical composition ... 6

10 Mechanical properties at room temperature and low temperatures ... 7

11 Mechanical properties at elevated temperature ... 7

12 Sampling and preparation of test pieces ... 8

13 Mechanical test methods ... 9

14 Retests ... 10

15 Inspection ... 10

16 Marking ... 11

Annexes A (normative) Options ... 12

B (informative) Ruling section and equivalent thickness ... 15

Foreword

This European Standard has been prepared by Technical Committee ECISS/TC 28

”Steel forgings”, the secretariat of which is held by BSI.

This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 1998, and conflicting national standards shall be withdrawn at the latest by July 1998.

The titles of the other Parts of this European Standard are:

– Part 2 : Ferritic and martensitic steels with specified elevated temperature properties.

– Part 3 : Nickel steels with specified low temperature properties.

– Part 4 : Weldable fine grain steels with high proof strength.

– Part 5 : Martensitic, austenitic and austenitic-ferritic stainless steels.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

(5)

Sida 2 EN 10222-1:1998

Innehåll

Sida

Förord ... 2

1 Omfattning ... 3

2 Normativa hänvisningar ... 3

3 Definitioner ... 4

4 Klassificering och beteckning ... 4

5 Information som skall lämnas av köparen ... 4

6 Ståltillverkning ... 5

7 Tillverkning av produkter ... 5

8 Ytbeskaffenhet och frihet från inre fel ... 6

9 Kemisk sammansättning ... 6

10 Mekaniska egenskaper vid rumstemperaturer och låga temperaturer ... 7

11 Mekaniska egenskaper vid förhöjd temperatur ... 7

12 Uttag och beredning av provstavar ... 8

13 Mekaniska provningsmetoder ... 9

14 Omprovning ... 10

15 Kontroll ... 10

16 Märkning ... 11

Bilaga A (normativ) Optioner ... 12

Bilaga B (informativ) Tvärsnitt och ekvivalenta tjocklekar ... 15

Förord

Denna europastandard har utarbetats av CEN/TC 28, Smide av stål. Sekretariatet hålls av BSI.

Denna europastandard skall ges status som nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast juli 1998, och mot- stridande nationella standarder skall dras in senast juli 1998.

Titlarna på de övriga delarna i denna europeiska standard är:

– Del 2: Ferritiska och martensitiska stål med fordrade egenskaper vid förhöjd temperatur.

– Del 3: Nickelstål med fordrade egenskaper vid låg temperatur.

– Del 4: Svetsbara finkornstål med förhöjd sträckgräns.

– Del 5: Martensitiska, austenitiska och austenit-ferritiska rostfria stål.

Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.

(6)

Page 3

EN 10222-1:1998

1 Scope

This Part of this European Standard specifies the general technical delivery condi- tions for open die steel forgings, ring rolled products and forged bars for pressure purposes.

General information on technical delivery conditions is given in EN 10021.

2 Normative references

This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.

EN 287-1 Approval testing of welders. Fusion welding. Part 1 : Steels EN 288 Specification and qualification of welding procedure for fusion

welding

Part 1: General rules

Part 2: Welding procedure specification for arc welding of metal- lic materials

Part 3: Welding procedure tests for arc welding of steels

EN 10 002-1 Metallic materials – Tensile testing – Method of test (at ambient temperature)

EN 10 002-5 Metallic materials – Tensile test – Method of test at elevated temperatures

EN 10 020 Definition and classification of grades of steel

EN 10 021 General technical delivery requirements for iron and steel pro- ducts

EN 10 027 Designation system for steel

Part 1 : Steel names, principal symbols Part 2 : Steel numbers

EN 10 045-1 Metallic materials – Charpy impact test – Test method EN 10 052 Vocabulary of heat treatment terms for ferrous products EN 10 079 Definition of steel products

EN 10 204 Metallic products – Inspection documents prEN 10228 Non-destructive testing of steel forgings.

Part 1. Magnetic particle inspection.

Part 2. Penetrant testing.

Part 3. Ultrasonic testing of ferritic or martensitic steel forgings.

Part 4. Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings.

EURONORM 168 Iron and Steel products – Inspection documents – Contents

(7)

Sida 3 EN 10222-1:1998

1 Omfattning

Denna del av EN 10222 anger allmänna tekniska leveransbestämmelser för fri- formsmide, valsade ringprodukter och smidda stänger för tryckbärande anord- ningar.

Allmänna tekniska leveransbestämmelser anges i EN 10021.

2 Normativa hänvisningar

Denna standard innehåller daterade eller odaterade hänvisningar till regler i andra publikationer. Dessa normativa hänvisningar återfinns i den löpande tex- ten. Publikationerna anges nedan. Beträffande daterade hänvisningar til publika- tioner som senare har ändrats eller fått tillägg, gäller dessa ändringar eller tillägg endast då de har införts i denna standard. Vid odaterade hänvisningar gäller den senaste utgåvan av publikationen.

EN 287-1, utg 2, Svetsarprövning – Smältsvetsning – Del 1: Stål

EN 288-1, utg 2, Specifikation för och godkännande av svetsprocedurer för svets- ning av metalliska material – Del 1: Allmänna regler för smältsvetsning

EN 288-2, utg 2, Specifikation för och godkännande av svetsprocedurer för svets- ning av metalliska material – Del 2: Svetsdatablad för bågsvetsning

EN 288-3, utg 2, Specifikation för och godkännande av svetsprocedurer för svets- ning av metalliska material – Del 3: Svetsprocedurkontroll för bågsvetsning av stål

EN 10002-1, utg 1, Metalliska material – Dragprovning – Del 1: Provningsmetod (vid rumstemperatur)

EN 10002-5, utg 1, Metalliska material – Dragprovning – Del 5: Metod för prov- ning vid förhöjd temperatur

EN 10020, utg 2, Definition och klassificering av ståltyper

EN 10021, utg 1, Allmänna tekniska leveransbestämmelser för järn- och stålpro- dukter

EN 10027-1, utg 1, Stålbeteckningar – Del 1: Alfanumeriskt system EN 10027-2, utg 1, Stålbeteckningar – Del 2: Numeriskt system

EN 10045-1, utg 1, Metalliska material – Slagprovning – Del 1: Provningsmetod EN 10052, utg 1, Termer för värmebehandling av järn- och stålprodukter EN 10079, utg 1, Definitioner av formvaror av stål

EN 10204, utg 1, Metalliska varor – Typer av kontrollintyg

EN 10228-1, utg 1, Oförstörande provning av stålsmiden – Del 1: Magnetpulver- provning

EN 10228-2, utg 1, Oförstörande provning av stålsmiden – Del 2: Penetrantprov- ning

EN 10228-3, utg 1, Oförstörande provning av stålsmiden – Del 3: Ultraljudsprov- ning av ferritiska och martensitiska stålsmiden

prEN 10228-4, utg 1, Oförstörande provning av stålsmiden – Del 4: Ultraljudprov- ning av austentiska och ferrit-austenitiska smiden i rostfritt stål

EURONORM 168, Iron steel products – Inspection documents – Contents

(8)

Page 4

EN 10222-1:1998

ENV 22605-1 Steel products for pressure purposes – Derivation and verifica- tion of elevated tempature properties –

Part 1: Yield or proof stress of carbon and low alloy steel prod- ucts

ENV 22605-2 Steel products for pressure purposes – Derivation and verifica- tion of elevated temperature properties –

Part 2: Proof stress of austenitic steel products

EN ISO 377 Steel and steel products – Location of samples and test pieces for mechanical testing.

prEN ISO 3651 Determination of resistance to intergranular corrosion stainless steels

Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stain- less steels – Corrosion test in media containing sulfuric acid CR10260 ECISS Information Circular 10. Designation systems for steel :

Additional symbols for steel names

CR 10261 ECISS Information Circular 11 – Iron and steel – Review of available methods of chemical analysis

3 Definitions

3.1 General

For the purposes of this Part of this European Standard the following definitions apply in addition to the definitions in EN 10 020, EN 10 021, EN 10 052, EN 10 079 and EN ISO 377.

3.2 batch: Forgings of similar dimensions from the same cast, made by the same forging procedure and from the same heat treatment charge.

4 Classification and designation

4.1 Classification

The steels in this European Standard are classified as follows:

Part 2: Non-alloy quality steels 1.0352, 1.0426 and 1.0436 – Alloy special steels – remaining steels.

Part 3: Alloy special steels

Part 4: Non alloy quality steels – 1.0477, 1.0478, 1.0565 and 1.0571 – Alloy spe- cial steels – 1.8932 and 1.8936.

Part 5: Alloy special steels.

4.2 Designation

The steels in Parts 2 to 5 of this European Standard are designated in accordance with the requirements of EN 10 027: Parts 1 and 2 and CR 10260.

5 Information to be supplied by the purchaser

5.1 Mandatory information

The purchaser shall select the steel type, the shape and dimensions of the forging taking the intended use into account.

(9)

Sida 4 EN 10222-1:1998

EN ISO 3651-2, utg 1, Bestämning av rostfria ståls härdighet mot korngränsfrät- ning – Del 2: Ferritiska, austenitiska och austenit-ferritiska (duplexa) rostfria stål – Korrosionsprovning i svavelsyrelösning (ISO 3651-2: 1998)

CR10260, ECISS IC 10 – Destignation systems for steel – Additional symbols for steel names

CR10261, ECISS IC 11 – Iron and steel – Review of available methods of chemical analysis

3 Definitioner

3.1 Allmänt

För denna europastandard gäller följande definitioner som tillägg till de i EN 10020, EN 10021, EN 10052, EN 10079 och EN ISO 377.

3.2 leveransparti: Smide, med närliggande dimensioner, från samma charge, till- verkade med samma smidesförfarande och från samma värmebehandlingscykel.

4 Klassificering och beteckning

4.1 Klassificering

Stålsorterna i denna europeiska standard är uppdelade enligt följande:

Del 2: Olegerade kvalitetsstål 1.0352, 1.0426 och 1.0436 – Legerade specialstål – övriga stålsorter.

Del 3: Legerade specialstål

Del 4: Olegerade kvalitetsstål – 1.0477, 1.0478, 1.0565 och 1.0571 – Legerade specialstål – 1.8932 och 1.8936.

Del 5: Legerade specialstål

4.2 Beteckning

Stålsorterna i del 2 till 5 i denna europeiska standard är benämnda enligt EN 10027: Del 1 och 2 och CR10260.

5 Information som skall lämnas av köparen

5.1 Obligatorisk information

Köparen skall välja stålsort, form och dimensioner för smidet med utgångspunkt från användningsområde.

(10)

Page 5

EN 10222-1:1998

The purchaser shall provide in the purchase order all the information necessary for describing the forging and its characteristics and details concerning delivery in- cluding the following :

I the quantity of forgings required;

II the forging dimensions, or the drawing number(s) containing the dimensions, tolerances and surface finish, to which the forgings shall conform;

III the steel designation of the material of which the forgings are made (see clause 4);

IV whether the purchaser needs to be informed of the forging procedure (see 7.2);

V whether production and testing of the forgings is to be witnessed by the pur- chaser's representative, and if so, the particular stages in production and testing at which the purchaser's representative may require to be present (see clause 15);

VI any required options (see 5.2 and annex A);

VII whether additional sample material is required for welding tests, the dimen- sions and location of such test pieces being agreed with the manufacturer;

VIII the type of inspection document in accordance with EN 10 204.

5.2 Options

A number of options are available and these are detailed in annex A. Where any of the options given are specified at the time of the order, the forgings shall conform to the requirements of any such option, in addition to the mandatory requirements of this Part of this European Standard.

If the purchaser does not specify any options at the time of enquiry and order, the manufacturer shall supply in accordance with the basic specification.

6 Manufacture of the steel

6.1 Steelmaking process

The steel shall be produced by an electric process or one of the basic oxygen proc- esses (see option A.1).

6.2 Deoxidation

The steel shall be fully killed.

7 Manufacture of the product

7.1 Hot working

The choice of hot working process shall be at the discretion of the manufacturer (see option A.2).

7.2 Forging reduction

The forging shall receive a sufficient forging reduction to completely consolidate the forging and remove the cast structure (see A.3).

7.3 Heat treatment

The forgings shall be heat treated as specified in the relevant Part of EN 10222, unless otherwise agreed at the time of enquiry and order.

7.4 Weldability

The steels in this European Standard are generally regarded as being weldable.

Welding shall be carried out in accordance with EN 287 and EN 288.

(11)

Sida 5 EN 10222-1:1998

Köparen skall i inköpsordern ange all nödvändig information för att beskriva smi- desdetaljen och dess egenskaper enligt följande:

I önskat antal smidesstycken;

II ange mått på smidesstycket eller ritningsnummer innehållande dimensio- ner, toleranser och ytfinish för smidesstyckets slututförande;

III stålbeteckningen på materialet som smidesstycket tillverkats av (se avsnitt 4);

IV om köparen behöver information om smidesförfarandet (se 7.2);

V om produktion och provning av smidesstyckena skall övervakas av inköpa- rens representant, och om så är fallet, de speciella faser i tillverkning och provning som representanten bör närvara vid (se avsnitt 15);

VI någon önskad valfri information (se 5.2 och bilaga A);

VII om ytterligare provmaterial önskas för svetsprovning, skall sådana provsta- vars mått och läge överenskommas mellan köpare och säljare;

VIII typ av kontrollintyg enligt EN 10204.

5.2 Valfri information (optioner)

Ett antal alternativ för valfri information (optioner) är angivna och beskrivs i bi- laga A. Om något av de givna alternativen är angivna vid beställningstillfället, skall smidesstycket uppfylla det begärda alternativet i tillägg till de obligatoriska kraven i denna EN.

Om inköparen inte anger något alternativ vid förfrågan och beställningstillfälle, skall tillverkaren leverera i enlighet med grundspecifikationen.

6 Ståltillverkning

6.1 Ståltillverkningsmetod

Stålet skall tillverkas i en elektrougn eller enligt en syrgasblåsningsmetod (se option A.1).

6.2 Desoxidation Stålet skall vara heltätat.

7 Tillverkning av produkter

7.1 Varmsmide

Val av varmsmidesmetod skall göras av tillverkaren (se option A.2).

7.2 Smidesreduktion

Smidesstycket skall reduceras tillräckligt, för att få en fullständig genombearbet- ning av smidet och eliminera gjutstrukturen (se A.3).

7.3 Värmebehandling

Smidesstycken skall värmebehandlas som anges i relevant del av EN 10222, om inget annat överenskommits vid förfrågan eller beställningstillfället.

7.4 Svetsbarhet

Stålsorterna i denna europastandard anses generellt vara svetsbara. Svetsningen skall utföras i enlighet med EN 287 och EN 288.

References

Related documents

Denna ändringsutgåva till europastandarden EN 288-2:1992 skall ges samma status som en nationell standard, antingen genom publicering av den identiska texten eller genom

Om dessutom ytterligare prov skall utföras för att göra godkännandet tekniskt likvärdigt, behöver de ytterligare proven endast utföras med ett prov- stycke enligt denna

Detta tillägg till europastandarden EN 288-3:1992 skall ges samma status som en nationell standard, antingen genom publicering av den identiska tex- ten eller genom

Technical delivery conditions for non-alloy quality steels - it was decided to prepare a standard for boron-alloy quenched and tempered steels as Part 3 of EN 10 083. For the

För tillägg till eller ändringar i daterade referensdokument gäller att de skall tillämpas vid användning av denna europastandard endast när så har angivits i ett tillägg till

I fall av tvist angående leverans av produkter med större diameter än som angetts tabell 10 i EN 10263-4:2001, skall provstaver formas genom varmbearbetning eller smidning till

Denna Europastandard EN ISO 15607:2003 skall ges status av nationell standard, antingen genom publice- ring av en identisk text eller genom ikraftsättning senast juni 2004,

This part of ISO 11199 includes all walking tables with three or more wheels or tips against the walking surface and having arm supports in the shape of a horizontal supporting