•
m[]W
McCormick"[INTER NATI O NAL
~
j
®
23 and 24 Beet Harvesters
INT [RNATIONAL HAR\/[ST[R
• Exclusive adjustable-angle puller
wheels
#
.
.,·
~
...
• Tandem
wheels excel for good floatation
•
Operating convenience saves
time
and effort
•
Extra strength construction for longer
I
ife
•
Big
144 cubic-foot tank holds upto
7500
lb of
beets
Now, harvest beets fast at a
ton-a-minute • . . load
'em
out clean, with
minimum tare! New McCormick
In-ternational two-row 23 and 24 Beet
Harvesters do unsurpassed pulling in
any soil, even under cloddy, muddy, or
rocky conditions. From puller wheels
to unloading elevator, these harvesters
are built to get your beets out fast •..
and get them clean. The big
144-cubic-foot tank lets you harvest without a
truck in the field. And built-in strength
in
every detail assures you of many
•
35
ft. of aggressive straight
through
cleaning bed
seasons of efficient harvesting.
Pull beets as fast as 5 miles per
hour with a 23 or 23 Beet Harvester.
Beets flow
in
a
fast,
unrestricted
stream from puller wheels to tank.
The cleaning bed
is
wide, to spread
beets across the full 34-inch-width of
the high-capacity rear elevator. Beets
move straight back, then up-and-over
rear elevator into the tank. There are
no lateral turns .•. no bottle necks.
Clearance between cleaning bed and
tank, for example, is a big 15½ inches.
Steerable Puller-Unit
Saves Beets Others Miss
You can guide ·puller wheels 4 inches to the right or to the left, with just a touch of the tractor hydraulic control. The entire puller unit (shown at left in red) is positioned later-ally inside the frame, by hydraulic cylinder (A). Steering is quicker and more precise than where a steerable hitch is used, because you move puller wheels only, and not the massive (up to 7 tons) weight of the harvester and beets irr the tank. You'll save more beets where short headlands, rough ground, or washouts make steering difficult. Fuller wheels are raised or lowered hydraulically, too, with cylinder (B).
SPECIFICATIONS
and
ATTACHMENTS
Row Spacings . . . . R..irvesting Capacity . . . . .
Tank Capacity lbs. -- Heaped
Tank Capacity lbs. -- Struck .
Tank Capacity -- Cubic Feet -- Heaped Tank Capacity -- Cubic Feet -- Struck Tire Size . . . .
Height of Elevator Shaft -- Regular . . . . . . . Height of Elevator Shaft with 24" Elevator Extension Overall Max. Width at Ground Line . . . . . . . .
Overall Max. Width at top of Elevator with Hood . . .
Overall Max. Width at top of Elevator with 24" elevator extension and hood . . . . . . . . . . Overall Height . . . . . . . Overall Height with 24" elevator extension . . . . Overall Length . . . . . . . . . . . . . . . . . . . . . . . Weight LBS . . . .
Time to Unload Tank . . . . . . . .
Conveyor Chain . . . . . . . . . . . . Side Elevator. . . . . . . Rear Elevator . . . . . . . . . . . .
Number of Cleaning Shafts . . . . Number of Kicker Wheels -- Hexagon . . . . . . .
Number of Kicker Wheels -- 4 point .
Number of Kicker Wheels -- 3 point . . . .
Cleaning Bed Area Sq. Ft. . . . Number of Sealed Bearings . . . . . Number of Tapered Roller Bearings . . . .
Total Number of Bearings, All Types . . .
Horsepower R~quired Minimum L • • • • • • • • • • • • •
Total Number of Lubrication Fittings .
Number of Fittings to Grease Daily . . . . . .
ATTACHMENTS AVAILABLE
Clod Crushers, for extremely hard ground . . . . . . . . Cleaning Rolls Mud Scrapers, for muddy conditions . . . Rubber Spacers for Cleaning Rolls, for rocky conditions. Elevator Extension 24", for loading high trucks. • . . .
Puller Wheel Spoke Att., for use in small beets . . • . .. Spring Loaded Mud Scrapers for puller wheels .
Stationary Mud Scrapers for Puller wheels . . . . . . . .
#23
20" -22" 1 ton per min. 7,500 lbs. 6,350 lbs. 170 cu. ft. 144 cu. ft. 4-7:50 X 16 6 ply 11' 11' 8" 120" 191" 215" 12'7" 13' 3" 192" 6300 90 seconds 7 /16 diameter 2-3/8 pitch 26" wide 34" wide 7 13 13 62 12 68 16 107 35 30 10 #23 X X X X X X X
Specifications subject t.t, change without notice.
INTERNATIONAL HARVESTER COMPANY 180 NORTH MICHIGAN AVE.• CHICAGO 1, ILLINOIS
CR•2200-N. 12•10-M LITHOGRAPHED IN UNITED STATES OF AMERICA
#24
28" -30" -32 "-34"
1 ton per min. 7,500 lbs. 6,350 lbs. 170 cu. ft. 144 cu. ft. 4-7. 50 X 16 6 ply 11' 11'8'" 138" 211" 235" 12'7" 13' 3" 192"' 6500 90 seconds 7/16 diameter 2-3/8 pitch 26" wide 34" wide 7 13 16 70 14 68 16 107 35 30 10 #24 X X X X X X X