SVENSK STANDARD SS-EN 13246
Fastställd Utgåva Sida
2001-05-04 1 1 (1+13)
© Copyright SIS. Reproduction in any form without permission is prohibited.
ICS 55.040
Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard.
Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08 - 610 30 00. Telefax: 08 - 30 77 57 E-post: sis.sales@sis.se. Internet: www.sisforlag.se
Upplysningar om sakinnehållet i standarden lämnas av SIS (STG).
Telefon: 08 - 13 62 50. Telefax: 08 - 618 61 28 E-post: info@stg.se
Tryckt i juni 2001
Packaging – Specification for tensional steel strapping
The European Standard EN 13246:2001 has the status of a Swedish Standard. This document con- tains the official English version of EN 13246:2001.
Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.
Förpackningar – Specifikation för stålband avsedda för bandning
Europastandarden EN 13246:2001 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 13246:2001.
Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13246
April 2001
ICS 55.040
English version
Packaging - Specification for tensional steel strapping
Emballage - Spécifications relatives aux cerclages d'acier Verpackung - Spezifikation für Umreifungsbänder aus Stahl
This European Standard was approved by CEN on 18 January 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T É E U R O P É E N D E N O R M A L I S A T I O N E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN 13246:2001 E
Page 2
EN 13246:2001
Contents
PageForeword...3
1 Scope ...4
2 Normative references ...4
3 Requirements...4
4 Coil sizes and weights...8
Annex A (informative) Finishing ...10
Annex B (informative) Bend test ...11
Bibliography ...13
Page 3 EN 13246:2001
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 261 "Packaging", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latest by October 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Page 4
EN 13246:2001
1 Scope
This European Standard specifies the dimensions and physical properties of a range of tensional steel strapping used to secure, close or strengthen packages and to band unit loads.
The types of tensional steel strapping covered by this European Standard and their characteristics are listed in Table 1.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments).
EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test (at ambient temperature)
3 Requirements
3.1 Mechanical properties
The minimum tensile strength and percentage elongation at break of tensional steel strapping in the specified range shall be as shown in Table 2 when tested in accordance with EN 10002-1, using a test piece of the original strapping using a gauge length of 100 mm.
3.2 Dimensions
The nominal width and nominal thickness of the specified range shall be as shown in Table 2. The tolerance ranges applicable to width and thickness shall be as shown in Tables 3 and 4.
Page 5 EN 13246:2001
Table 1 — Types of tensional steel strapping TypeMaterialCharacteristics 1Cold rolled bright steelLow tensile strength 2.1Cold rolled and tempered steelMedium tensile strength (Standard packaging quality) 2.2Cold rolled and tempered steelHigh tensile strength - Low elongation 3.1Cold rolled, heat treated steelMedium tensile strength - Very high elongation 3.2Cold rolled, heat treat steelHigh tensile strength - High elongation 3.3Cold rolled, heat treated steelVery high tensile strength
Page 6
EN 13246:2001
Table 2 — Dimensions and mechanical properties Type 1Type 2.1Type 2.2Type 3.1Type 3.2Type 3.3 NominalNominalMinimumMinimumMinimumMinimumMinimumMinimum WidthThickTensileTensilePercentTensilePercentTensilePercentTensilePercentTensilePercent mmmmN/mm2 N/mm2 ElongationN/mm2 ElongationN/mm2 ElongationN/mm2 ElongationN/mm2 Elongation 9,50,46507500,59000,5 0,56507501,09000,5 12,70,46507500,59000,5 0,56507501,09000,59256 0,66507501,09000,5 160,46507500,5 0,56507501,09000,5925612503 0,66507501,0925612503 190,56507501,0750129256 0,66507501,0 0,636007501,09000,575012925612503 0,76007001,0925612503 0,86007002,09000,575012925612503 0,96007002,075012925612503 25,40,636007501,0 0,86007002,09000,5750129256 0,96007002,075012 1,06007002,0 31,750,86007002,09000,5750129256 0,96007002,075012 1,06007002,075012