SVENSK STANDARD SS-EN 12963
Fastställd Utgåva Sida
2001-07-27 1 1 (1+7)
© Copyright SIS. Reproduction in any form without permission is prohibited.
ICS 83.180
Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard.
Postadress: SIS Förlag AB, 118 80 STOCKHOLM Telefon: 08 - 555 523 00. Telefax: 08 - 555 523 11 E-post: sis.sales@sis.se. Internet: www.sisforlag.se
Upplysningar om sakinnehållet i standarden lämnas av SIS.
Telefon: 08 - 555 520 00. Telefax: 08 - 555 520 01
Tryckt i september 2001
Adhesives – Determination of free monomer content in adhesives based on synthetic polymers
The European Standard EN 12963:2001 has the status of a Swedish Standard. This document con- tains the official English version of EN 12963:2001.
Swedish Standards corresponding to documents referred to in this Standard are listed in ”Catalogue of Swedish Standards”, issued by SIS. The Cata- logue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards.
Lim – Bestämning av innehåll av fria monomerer i lim baserade på syntetiska polymerer
Europastandarden EN 12963:2001 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN 12963:2001.
Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna stan- dard framgår av ”Katalog över svensk standard”, som ges ut av SIS. I katalogen redovisas interna- tionella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12963
April 2001
ICS 83.180
English version
Adhesives - Determination of free monomer content in adhesives based on synthetic polymers
Adhésifs - Détermination de la teneur en monomères libres dans des adhésifs à base de polymères synthétiques
Klebstoffe - Bestimmung des freien Monomeranteils in Klebstoffen auf der Basis synthetischer Polymere
This European Standard was approved by CEN on 1 March 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T É E U R O P É E N D E N O R M A L I S A T I O N E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN 12963:2001 E
Page 2
EN 12963:2001
Contents
Page
Foreword...3
1 Scope ...4
2 Normative references ...4
3 Terms and definitions ...4
4 Principle...4
5 Safety ...4
6 Chemicals...4
7 Apparatus ...5
8 Sampling and sample preparation...5
9 Chromatographic conditions ...5
10 Calibration of the gas chromatograph ...6
11 Procedure ...6
12 Expression of results ...7
13 Test report ...7
Page 3 EN 12963:2001
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 193 "Adhesives", the secretariat of which is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latest by October 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Page 4
EN 12963:2001
1 Scope
This European Standard specifies a simple test method for the gas-chromatographic determination of free monomer content in polymeric adhesives after specific treatment.
This test method can be used for the determination of acrylic, styrene, vinyl and other unsaturated monomers.
NOTE This method could also be used for the determination of other monomers, if applicable.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments).
EN 923 Adhesives — Terms and definitions
EN 1066 Adhesives — Sampling
EN 1067 Adhesives — Examination and preparation of samples for testing
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 923 apply.
4 Principle
4.1 Water-borne adhesives
An aliquot of an extract of the water-borne adhesive to be analysed is injected into a gas chromatograph equipped with a capillary column and a linear temperature programmer. The monomers are detected by a Flame Ionisation Detector (FID). Quantification is made by peak area measurement.
4.2 Solvent-borne or solvent-less adhesives
An aliquot of the solvent-borne or solventless adhesive is diluted with a suitable solvent. The solvent shall be able to considerably reduce the viscosity of the adhesive solution as to allow it to be injected into the gas
chromatrograph. The solvent shall not interfere with the monomers to be detected. The diluted solution is analysed as the extract as described in 4.1
5 Safety
Persons using this standard shall be familiar with normal laboratory practice.
This standard does not purport to address all the safety problems, if any, associated with its use.
It is the responsibility of the user to establish safety and health practices and to ensure compliance with any European or national regulatory conditions.
6 Chemicals
All the chemicals used for the test shall be of analytical grade.