A C T U AT O R L A 3 1 C A R E L I N E
LA31C: 24 V DC. Max. thrust 6000 N
Features:
• 24 V DC permanent magnet motor
• Thrust up to 6000 N in push and up to 4000 N in pull
• Electric chromated steel piston rod eye with slot
• Duty cycle: Max. 10% or 2 minutes continuous use followed by 18 minutes not in use
• Ambient temperature +5°C to +40°C
• High-strength plastic housing protects motor and gears
• Elegant and compact design with small installation dimensions
• Standard protection class: IP 54
• Colour: black
• 2.30 m straight cable
• Built-in limit switches (not adjustable)
• Scratch and wear-resistant powder painting on outer tube Ø30 mm
• Zinc alloy back fixture
• Strong wear and corrosion resistant stainless steel inner tube
• Noise level 45 dB (A); measuring method DS/EN ISO 3746, actuator not loaded.
• The CARELINE system has full compliance with EN 60601-1
Options:
• LA31 Basic version CARELINE® (no slot in piston rod eye)
• Flexible back fixture
• Reed switch (8 pulses per spindle revolution) for exact position- ing of memory control and compatibility with CB9P
• Fast motor
• Mechanical splines (the actuator can only push)
• Jack plug for use with other control boxes than CB9
• Protection class IP 66. Not for wash tunnels!
• Quick release on LA31 (different types of release handle)
The LA31 actuator is a very quiet and powerful actuator designed for a variety of applications such as furniture, care or hospital beds. The standard LA31 actuator is avail- able for both the HOMELINE®, CARELINE® and DESKLINE® product range.
Due to its high capacity, design and protection class up to IP 66 the CARELINE® actuator is ideal for the care sector e.g. for beds. The CARELINE® LA31 actuator is available as a standard or a Basic version. The standard LA31 actua- tor features known parts such as piston rod eye with slot. The Basic version is a special cost optimised version, which is compatible with the CB9 Basic control box. The LA31 Basic actuator is also available in a special version with a fast motor.
WE IMPROVE YOUR LIFE
Dimensions LA31
LINAK A/S LA31002C
INSTALLATIONDIM.=STROKE + ADDITION
80.75 23.5
27.5
153
7.4
62.9
47
.
152.75 78
163
Standard installation dimensions with different combinations of Piston Rod Eyes and back fi xtures to LA31.
length>115mm length<115mm
LA31 Standard LA31 Quick release
S + 176mm
288mm S + 189mm 289mm
1/2 and 7/8 Back Fixture
Eye
LA31 Splines
0, 1, 2 and 3 0, 1, 2 and 3 0, 1, 2 and 3 0, 1, 2 and 3 With Qr With Qr length>100mm length<100mm length>115mm length<115mm
S + 173mm 288mm S + 189mm 289mm
5/6 342mm
Stroke Stroke Stroke Stroke Stroke Stroke
A/B
S + 173mm
291mm S + 192mm 292mm
S + 227mm
Minimum installation dimension is 288 mm.
Minimum installation dimension with splines is 289 mm.
Minimum installation dimension with quick release is 342 mm
With Mechanical End-stop the installation dimension is increased by 20 mm Options:
• 0.2/0.4 m coiled cable with DIN or Jack plug
• Colour: grey
• Safety nut in push
• Mechanical End stop
Dimensions LA31 with CB9
Back fi xtures:
Piston Rod Eyes:
The LA31 actuator must not be exposed to more than 4000 N in pull. In applications were misalignments may occur the normal back fixture can take max. 1500 N in pull where as the flexible back fixture can take up to 4000 N in pull.
If an LA31 is used in an application where there are repeated dynamic pulling movements in the area 2000 - 4000N, then it is necessary to contact the Technical Support department in order to make a correct specification of the actuator.
LA31 CARELINE Ordering example
0
31 1 1 0 - 0 0 10 0 0 2 0
IP-Degree:
Motor type:
Stroke length:
Brake:
Options: Spindle
Colour:
Options: Position
0 = None
- = Black 2 = Splines
0 = None
I = Quick-release std. grip (Q2) 2 = IP66
0 = 24 V DC Standard 1 = 24 V DC Basic L1
XXX = mm
1 = Brake push 2 = Brake pull
1 = Safety nut 0 = None
+ = Grey
Piston Rod Eye:
Back fixture:
Spindle type:
Actuator type:
3 = Standard gold chrom.
0 = Standard with slot, and quick-release 1 = Standard solid
2 = Standard painted
7 - 8 = Solid
1 - 2 = Standard with 10 mm slot 5 - 6 = Flexible
3 = 9 mm 1 = 3 mm 2 = 5 mm
4 = 4 mm 6 = 12 mm 7 = 6 mm 31 = LA31
Cables: DIN cables
A = Straight 2,25 m J = Straight 0,80 m F = Straight 1,50 m B = Straight 1,00 m G = Straight 0,75 m H = Straight 0,50 m E = Straight 0,25 m C = Coiled 0,40 m D = Coiled 0,20 m Jack cables
0 = Straight 2,25 m 5 = Straight 0,80 m 6 = Straight 1,50 m 1 = Straight 1,00 m 7 = Straight 0,75 m 8 = Straight 0,50 m 9 = Straight 0,25 m 2 = Coiled 0,40 m 3 = Coiled 0,20 m
3 = Splines with safety nut 4 = IP54
3 = 24 V DC Basic fast motor L3
K = Quick-releaes bowden cable (Q1) L = Quick-release side grip (Q3) M = Quick.release without grip (Q0)
R = Reed
When mounting CB E = Straight 0,25 m (IP54 / IP66)
4 = Mechanical End Stop
5 = Mechanical End Stop + safety nut
A - B = Standard with 12 mm slot
Comments to table:
* LINAK control boxes are designed so that they will short-circuit the motor terminals (poles) of the actuator(s), when the actuator(s) are not running. This solution gives the actuator(s) a higher self-locking ability. If the actuator(s) are not connected to a LINAK control box, the terminals of the motor must be short-circuited to achieve the self-locking ability of the actuator.
** When the load in push is above 4000 N (max. 6000 N), the max. stroke length is 250 mm.
11/7
27/20
3 6000 6/4 6000
5 4000 2000
5 4000 11/7 4000
9 1500 19/15 1500
12 1000 1000
4 6000 8/4 6000
6 2500 13/9 2500
Standard 24 V motor
31.131.2
31.2 With brake 31.3 With brake 31.6 With brake 31.4 With brake 31.7 With brake
3 6000 8/4 6000
5 4000 14/8 2000
5 4000 14/8 4000
9 1500 27/18 1500
12 1000 33/25 1000
4 6000 11/5 6000
Fast 24V motor
31.131.2 With brake 31.2
31.3 With brake
31.4 With brake 31.6 With brake
6 2500 17/12 2500
31.7 With brake
Standard 24V motor and Quick release
6 2500 13/9 2500
31.7 With quick release Max. load to release: 50 kg
5 3500
4000 4000 4000 1500 1000 4000 2500
4000 4000 4000 1500 1000 4000 2500
200 200
3.5 2.9 3.5 1.8 2.2 4.3 2.2
(mm) (N) (mm/s) (N)
Spindle pitch
Max. load Push
Typical speed 0/Full load Push Spindle type
(N) Pull
(N) Typical
Amp.
4.1 2.9 4 2.4 2.2 5.1 2.7
2.2
3.5 11/7 3500
31.2 With quick release Max. load to release: 75 kg
Fast 24V motor and Quick release
31.7 With quick release Max. load to release: 50 kg 31.2 With quick release Max. load to release: 75 kg
Self-lock Max.
4000 2000 4000 1500 1000 4000 2500
4000 2000 4000 1500 1000 4000 2500
0 (N) Push
0
6 2500 17/12 2500
5 3500
200 200
2.7
4 14/8 3500
0 0 Technical specifi cations:
Current consumption[A]
0 N 500 1000 1500 2000
Thrust [N]
0 1 2 3
Spindle type 7 with brake and CB90
10 12
AMP Speed 8 2500
Current consumption[A]
0 N 0 1 2 3
Spindle type 2 with brake and CB90
Speed[mm/sec.]
6 10
8 12
Thrust [N] AMP Speed
4
2000 3000 4000
1000
Current consumption[A]
0 N 1000 1500 2000
0 1 2 3
Spindle type 2 and CB90
Speed[mm/sec.]
6 10 12
8
500
Thrust [N] AMP Speed
14
Current consumption[A]
0 N 0,0 0,5 1,0 1,5
Spindle type 3 with brake and CB90
Speed[mm/sec.]
12 16 20
14 18
Thrust [N] AMP Speed
2,0
600 900 1200 1500
300
Current consumption[A]
0 N 0 1 2 3
Spindle type 4 with brake and CB90
Speed[mm/sec.]
2 6 10
4 8
Thrust [N] AMP Speed
4
4000 6000
2000 Current consumption[A]
0 N 0 1 2 3
Spindle type 1 and CB90
Speed[mm/sec.]
3 5 7
Thrust [N] AMP Speed
4
4000 6000
2000
Current consumption[A]
0 N 200 400 600 800
Thrust [N]
0 1 2
3 Spindle type 7 with brake and CB90
22 25
AMP Speed 19 1000
28 Graphs: Standard Motor
Specifications subject to change without prior notice.
It is the responsibility of the product user to determine the suitability of LINAK A/S products for a specific application. LINAK will at point of delivery replace/repair defective products covered by the warranty if promptly returned to the factory. No liability is assumed beyond such replacement/repair.
Copyright © LINAK 10.02 MA M9-02-058 . Chapter 5.8.2
Current consumption[A]
0 N 0 1 2 3
Spindle type 3 with brake and CB90
Speed[mm/sec.]
17 21 25
19 23
Thrust [N] AMP Speed
600 900 1200 1500
300
Current consumption[A]
0 N 0 2 4
Spindle type 4 with brake and CB90
Speed[mm/sec.]
4 8 12
6 10
Thrust [N] AMP Speed
6
4000 6000
2000 Current consumption[A]
0 N
Thrust [N]
0 2
Spindle type 1 and CB90
Speed[mm/sec.]
3 7
5 9
AMP Speed
1 3
4000 6000
2000 4
5
Current consumption[A]
0 N 2000 4000
0 1 2 3
Spindel type 2 with brake and CB90
Speed[mm/sec.]
7 11 13
9 15
1000
Thrust [N] AMP Speed
4 5
3000
Current consumption[A]
0 N
Thrust [N]
0 2
Spindle type 6 with brake and CB90
Speed[mm/sec.]
24 28 32
26 30 34
AMP Speed
1 3
400 600 800 1000
200
Current consumption[A]
0 N 0 1 2 3
Spindle type 7 with brake and CB90
Speed[mm/sec.]
10 14 18
12 16
Thrust [N] AMP Speed
1000 1500 2000 2500
500
Current consumption[A]
0 N 0 1 2 3
Spindle type 2 and CB90
Speed[mm/sec.]
7 11 15
9 13
Thrust [N] AMP Speed
1000 1500 2000
500
27 Graphs: Fast Motor