SIS - Standardiseringskommissionen i Sverige
SVENSK STANDARD SS-EN 10131
Handläggande organ Fastställd Utgåva Sida
SIS - MATERIALNORMCENTRALEN 1992-05-27 1 1 (1+6+6)
SIS FASTSTÄLLER OCH UTGER SVENSK STANDARD SAMT SÄLJER NATIONELLA OCH INTERNATIONELLA STANDARDPUBLIKATIONER ©
Kallvalsade obelagda, mjuka och höghåll- fasta platta produkter av stål för kallform- ning – Toleranser för dimensioner och form
Orientering
Denna standard utgörs av både den svenska och den eng- elska versionen av europastandarden EN 10131:1991.
Vid tryckningen har de två versionerna lagts sida mot sida, men numrerats löpande, så att varje uppslag numrerats som en sida.
Standarden ersätter SS 21 12 10.
EN 10131 är en revidering av EURONORM 131-77
Cold rolled uncoated low carbon and high yield strength steel flat products for cold forming – Tolerances on dimensions and shape
Introduction
This standard consists of the Swedish and the English version of the European Standard EN 10131:1991.
The two versions are printed with the pages side by side, but are numbered in consecutive order, so that each set of pages has only one page number.
This standard replaces SS 21 12 10.
EN 10131 is a revision of EURONORM 131-77
UDK 669.14-122.2-41:621.753.1
Standarder kan beställas hos SIS som även Iämnar all- Upplysningar om sakinnehållet i standarden Iämnas av SIS-MNC.
männa upplysningar om svensk och utländsk standard. Telefon: 08-644 93 75. Telefax: 08-640 87 25 Postadress: SIS, Box 3295, 103 66 STOCKHOLM
Telefon: 08 - 613 52 00. Telefax: 08 -11 70 35 Prisgrupp N Tryckt i september 1992
EUROPEAN STANDARD EN 10131
NORME EUROPÉENNE
EUROPÄISCHE NORM October 1991
UDC 669.14-122 .2-41 : 621.753.1
Descriptors: Iron and steel products, cold-rolled products, metal plates, wide, strips. low carbon steels, high yield strength steels, dimensional tolerances, form tolerances
Cold-rolled steel flat
English version
uncoated low carbon and high yield strength products for cold
dimensions
Produits plats laminés à froid, non revêtus, en acier doux et en acier à haute limite
d’élasticité pour emboutissage et pliage à froid – Tolérances sur les dimensions et sur la forme
forming – Tolerances on and shape
Kaltgewalzte Flacherzeugnisse ohne Überzug aus weichen Stählen sowie aus Stahlen mit höherer Streckgrenze zum Kaltumformen – Grenzabmasse und Formtoleranzen
This European Standard was approved by CEN on 25 October 1991. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 Brussels
© CEN 1991 Copyright, reserved to all CEN members
Ref. No. EN 10131: 1991. E
EUROPASTANDARD EN 10 131 EUROPEAN STANDARD
NORME EUROPÉNNE
EUROPÄISCHE NORM
Oktober 1991UDK 669.14- 122.2-41:621.753.1
Nyckelord: Järn-och stålprodukter, kallvalsade produkter, metallplåt, breda band, mjuka stål, höghållfast stål, dimensionstoleranser, formtoleranser
Svensk version
Kallvalsade obelagda, mjuka och höghållfasta platta produkter av stål för kallformning – Toleranser för dimensioner och form
Produits plats Iaminés à froid, Cold rolled uncoated low carbon Kaltgewalzte Flacherzeugnisse non revêtus, en acier doux et en and high yield strength steel flat ohne Überzug aus weichen acier à haute Iimite d’élasticité products for cold forming – Stählen sowie aus Stählen mit pour emboutissage et pliage à Tolerances on dimensions and höherer Streckgrenze zum froid – Tolérances sur Ies shape Kaltumformen – Grenzabmasse
dimensions et sur la forme und Formtoleranzen
Denna standard är den svenska versionen av EN 10131:1991. Den har översatts av SIS, Denna Europastandard antogs av CEN 1991-10-25.
CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECS interna bestämmelser som anger på vilka villkor denna Europastandard i oförändrat skick skall ges status som nationell standard.
Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centalsekretariat eller från någon av CENs medlemmar.
Denna Europastandard finns i tre officiella versioner (engelsk, fransk, tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat har samma status som de officiella versionerna.
CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irand, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tyskland och Österrike.
CEN
European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: Rue de Stassart 36, B-1050 BRUSSELS
© CEN 1991 Copyright reserved to all CEN members
Ref, Nr EN 10 131:1991 Sv
Page 2
EN 10131:1991
Foreword
13.3The European Committee for Iron and Steel 13.4 Standardization (ECISS) asked Technical
Committee 13 (Secretariat: Beigium) to transform 13.5 EU 131 : 1977 ‘Cold-rolled non-coated mild 13.6 unalloyed steel flat products for cold forming.
Tolerances on dimensions and shape’ into a European Standard and to enlarge its field of application to incorporate steels with high yield strength.
Publication of European Standard EN 10131 was agreed at a meeting of ECISS/TC 13 in October 1991, and accepted by COCOR on 1991-05-27 for submission to CEN formal vote.
This European Standard replaces the EURONORM 131-1977.
In accordance with the Common CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard:
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
Contents
1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 8 9 9.1 9.2 10 11 12 13 13.1 13.2
Scope
Normative reference Definitions
Designation
Condition of delivery Tolerances on thickness Low carbon steel flat products High yield strength steel flat products
Tolerances on width Sheet and wide strip Slit wide strip of width 600 mm
Tolerances on length Tolerances on flatness Low carbon steel sheet
less than
High yield strength steel sheet Tolerances on out-of-squareness Tolerances on edge camber Superimposement of dimensions Measurement
Thickness Length
Page 3 3 3 3 3 3 3 4 4 4 4 4 5 5 5 6 6 6 6 6 6
Page
Width 6
Flatness 6
Out-of-squareness 6
Edge camber 6
Sida 2 EN 10 131:1991
Förord Sida
Den europeiska kommittén för järn och stål stan- 13.3 Bredd dardisering (ECISS) ombad teknisk kommitté 13 13.4 Planhet (secretariat : Belgien) att omforma EU 131:1977 “Cold- 13.5 Rätvinklighet rolled non-coated mild unalloyed steel flat products for 13.6 Rakhet cold forming – Tolerances on dimension and shape” till
europastandard och att utvidga omfattningen genom att införliva höghållfast stål.
Utgivningen av europastandarden EN 10131 beslöts vid ett möte med ECISS/TC 13 i oktober 1991, och godkändes av COCOR 1991-05-27 för att framläggas för formell omröst- ning inom CEN.
Denna europastandard ersätter EURONORM 131-1977.
Enligt CEN/CENELEC’s allmänna regler är följande län- der förpliktigade att ikraftsätta denna europastandard Belgien, Danmark, Finland, Frankrike, Tyskland, Grek- land, Island, Irland, Italien, Luxemburg, Nederländerna, Norge, Portugal, Spanien, Sverige, Schweiz, Storbritannien och Österrike.
1 2 3 4 5 6 6.1 6.2 7 7.1 7.2 8 9 9.1 9.2 10 11 12 13 13.1 13.2
Sida
Omfattning 3
Referenser 3
D e f i n i t i o n e r 3
Beteckningar 3
Leveransvillkor 3
Tjocklekstoleranser 3
Mjuka platta stålprodukter 3
Höghållfasta platta stålprodukter 4
Breddtoleranser 4
Breddtoleranser för plåt och bredband 4 Spaltat bredband med bredd mindre än 600 mm 4
Längdtoleranser 4
Planhetstoleranser 5
Mjuk stålplåt med Re < 280 N/mm2 5
Höghållfast stålplåt 5
Tolerans för rätvinkelhet 6
Toleranser för rakhet 6
Inskrivning av dimensioner 6
Mätningar 6
Tjocklek 6
Längd 6
6 6 6 6
Page 3
EN 10131:1991
1 Scope
This European Standard applies to cold-rolled uncoated low carbon and high yield strength steel flat products for cold forming with a minimum thickness of 0.35 mm and unless otherwise agreed at the time of ordering less than or equal to 3 mm thick, delivered in sheet, wide strip, slit wide strip, or cut lengths obtained from slit wide strip or sheet.
It does not apply to cold-rolled strip (rolled width
<600 mm), or to flat cold-rolled products for which there is a specific standard, in particular the following:
– cold-rolled non-grain oriented magnetic steel sheet and strip
(EURONORM
106);– semi-processed steel strip for the construction of magnetic circuits
(EURONORM
126 and 165);- blackplate in sheet form
(EURONORM
145);- blackplate in coils
(EURONORM
146);– cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EURONORM 139).
2 Normative reference
EN 10079 Definition of steel products
3 Definitions
For the purposes of this European Standard, the definitions of the cold-rolled flat products listed in clause 1 are those given in EN 10079.
4 Designation
4.1 Products conforming to this European Standard shall be designated in the following order (see also clause 5);
(a) type of product (wide strip, sheet or cut length);
(b) the number of this standard (EN 10131);
(c) nominal thickness in millimetres;
(d) the letter S for products ordered with special tolerances on thickness;
(e) nominal width in millimetres;
(f) the letter S for products ordered with special tolerances on width;
(g) nominal length in millimetres;
(h) the letter S for products ordered with special tolerances on length (sheets and cut lengths only);
(i) the letters FS for sheets or cut lengths ordered with special tolerances on flatness;
(j) the letters CS for slit strip ordered with special tolerances on camber.
4.2 The product designation in accordance with 4.1 shall be followed by the complete designation of the steel ordered (according to EN 10130 for example).
4.3 Examples of designation
(a) Wide strip according to this European
Standard of nominal thickness 1,20 mm, nominal width of 1500 mm in steel FePO4Am as specified in EN 10130.
Wide strip EN 10131 – 1,20 x 1500 Steel EN 10130- FePO4Am.
(b) Sheet according to this European Standard of nominal thickness 0,80 mm ordered with special
thickness tolerance (S), nominal width of 1200 mm with special tolerances on width(S), nominal
length of 2500 mm and with special tolerances on flatness in steel FePO6Bg as specified in
EN 10130:
Sheet EN 10131 – 0,80 S x 1200 S x 2500 FS Steel EN 10130 – FePO6Bg.
5 Condition of delivery
5.1 Flat products according to this European Standard may be delivered as follows:
(a) with normal or special thickness tolerances (see table 1);
(b) with normal or special width tolerances (see tables 3 and 4);
(c) with normal or special length tolerances for sheet or cut lengths (see table 5);
(d) with normal or special flatness tolerances for sheet or cut lengths (see tables 6 and 7);
(e) with normal or special tolerances on camber for slit strip of width less than 600 mm (see clause 11).
5.2 In the absence of information on the order in respect of the condition of delivery given in 5.1 the flat products shall be delivered with normal tolerances on thickness, width, length, flatness and camber.
6 Tolerances on thickness
The tolerances on thickness are given in 6.1 for low carbon steel flat products and in 6.2 for high yield strength steel flat products.
6.1 Low carbon steel flat products
The tolerances on thickness shall be as given in table 1 and apply over the whole length.
Tolerances more severe than special tolerances may be agreed at the time of the order.
Sida 3 EN 10131:1991
1 Omfattning
Denna europastanderd gäller för kallvalsade, obelagda, platta produkter av mjuka och höghållfasta stål, avsedda för kallformning med minsta tjocklek 0,35 mm, och om inte annat överenskommits vid beställning, med tjocklek mind- re eller lika med 3 mm, levererad i form av plåt, breda band, spaltade breda bend eller skurna längder av spaltade breda band eller plåt.
Den omfattar inte kallvalsade, smala band (valsad bredd 600 mm), eller andra kallvalsade, platta produkter, för vilka det fin en särskild standard, i synnerhet de följande:
2
- kallvalsad, icke-orienterad elektroplåt (EURO- NORM 106)
- tunnplåt för förpackningsändamål (EURO- NORM 145)
— tunnplåt i rulle för förpackningsändamål, prEN 10205
– kallvasade obelagda, olegerade, mjuka smalband av stål för kallformning (EURONORM 139).
Referenser
Denna europastandard innehåller genom hänvisning till daterade eller odaterade referenser, krav friån andra pub- likationer. Dessa bindande referenser nämns i texten och publikationerna anges nedan. För daterade referenser gäl- ler efterföljande tillägg och revideringar endast när de införlivas i denna standard genom tillägg eller revidering.
För odaterade referenser gäller senaste utgåvan refererade standarden.
SS-EN 10079 Deftitioner av formvaror för stål
3 Definitioner
av den
I denna europastandard används definitionerna i SS-EN 10079 för de kallvalsade platta produkterna som anges i avsnitt 1.
4 Beteckningar
4.1 Produkter som överensstämmer med denna europa- standard skall betecknas enligt följande ordning (se även avsnitt 5):
a) form (breda band, plåt eller skuren längd), b) denna standards nummer (EN 10 131), c) nominell tjocklek i millimeter,
d) bokstaven “S” för produkter beställda med förbätt- rade tjocklekstoleranser,
e) nominell bredd i millimeter,
f) bokstaven “S” för produkter beställda med förbätt- rade breddtoleranser,
g) nominell längd i millimeter,
h) bokstaven “S” för produkter beställda med förbätt- rade längdtoleranser (endast plåt och skurna längder), i) bokstäverna “FS’> för plåt och skurna längder be- ställda med förbättrade planhetstoleranser,
j) bokstaven “CS” för spaltat band beställd med för- bättrade rakhetstoleranser.
4.2 Produktbeteckningen enligt 4.1 skall efterföljas av fullständig beteckning för den beställda stålsorten (exem- pelvis enligt EN 10 130).
4.3 Exempel på beteckningar
a) Breda band enligt denna europastandard med no- minell tjocklek 1,20 mm, nominell bredd 1500 mm av stålsorten Fe P04 Am enligt EN 10130
Breda band EN 10131 – 1,20 x 1500 Stål EN 10130 – Fe P04 Am
b) Plåt enligt denna standard med nominell tjocklek 0,80 mm, beställd med förbättrad tjocklekstolerans (S), nominell bredd 1200 mm med förbättrad breddtolerans (S), nominell längd 2500 och med förbättrad planhets- tolerans av stålsorten Fe P06 Bg enligt EN 10130
Plåt EN 10 131 – 0,80 S X 1200 S X 2500 FS Stål EN 10 130 – Fe P06 Bg
5 Leveransvillkor
5. 1 Platta produkter enligt denna europastandard kan levereras enligt följande:
a) med normal eller förbättrad tjocklekstolerans (se tabell 1)
b) med normal eller förbättrad breddtolerans (se ta- bell 3 och 4)
c) med normal eller förbättrad längdtolerans för plåt och skurna längder (se tabell 5)
d) med normal eller förbättrad planhetstolerans för plåt och skurna längder (se tabell 6 och 7)
e) med normal eller förbättrad rakhetstolerans för spaltat band med bredd mindre än 600 mm (se av- snitt 11).
5.2 I avsaknad av information rörande leveransvillkor enligt 5.1 skall platta produkter levereras med normala toleranser för tjocklek, bredd, längd, planhet och rakhet.
6 Tjocklekstoleranser
Tjocklekstoleranser anges i 6.1 för mjuka platta stålpro- dukter och i 6.2 för höghållfasta stålprodukter.
6.1 Mjuka platta stålprodukter
Tjocklekstoleranserna skall överensstämma med tabell 1 och gälla över hela längden. Snävare toleranser än förbätt- rad tolerans kan överenskommas vid beställning.
Page 4
EN 10131:1991
6.2 High yield strength steel flat products 7.1 Tolerances on width of sheet and wide strip The thickness tolerances shall be as given in table 1 The tolerances on width of sheet and wide strip shall subject to the increases given in table 2 depending on be as given in table 3.
the yield strength.
7.2 Slit wide strip of width less than 600 mm The tolerances on width of slit wide strip of width less than 600 mm shall be as given in table 4.
7 Tolerances on width
The tolerances on width of flat products in low carbon
8 Tolerances on length
and high yield strength steels are given in 7.1 for The tolerances on length shall be as given in table 5 sheet and wide strip and in 7.2 for slit wide strip of and apply to all products covered by this standard width less than 600 mm. including low carbon and high yield strength steels.